If 192.168.1.1 works, 10.0.0.1 never will and if 10.0.0.1 works 192.168.1.1 wont. Both ar private IP addresses which means they are always on a local area network and behind a router. The two IPs cannot exist on the same network. All the ping
Online ping tool verifies accessibility of the host from the Internet by sending ping packets. Both IPv4 ping and IPv6 ping are supported. This ping tool uses ICMP packtes to check if remote host is accessible. In some cases the destination host may be configured not to reply to ICMP ping requests, or there might a firewall which blocks ICMP Definable size of a packet in bytes, from 1 to about 65500 bytes (parameter –s in the Unix systems, -l in Windows, e.g. ping –s 128 10.0.0.2 will cause transmission of a packet of the size of 128 bytes instead of the default 32). For example, PING 10.0.0.2; Understanding the results: Each PING test makes 4 tries, and gives back a response for each attempt. If the response looks like this, the test is successful. If the response looks like either of these examples, the test failed. Resolving the problem: There are several things that can cause a PING test to fail, such as: check your pc's ip setting by running ipconfig from the command line. You need to ensure that your local network setting is in the 10.0.0 range. try setting it to a manual setting of 10.0.0.100, Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds: Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/1 ms As you can see from the output, the ICMP replies were received. IP Address. The Internet Protocol (IP) knows each logical host interface by a number, the so-called IP address.On any given network, this number must be unique among all the host interfaces that communicate through this network.
Mar 20, 2002 · Computer B Ip address - 10.0.0.2 - SNM - 255.0.0.0 They each dial up to separate internet accounts via modem no gateway is assigned for either system on the NICs
If 192.168.1.1 works, 10.0.0.1 never will and if 10.0.0.1 works 192.168.1.1 wont. Both ar private IP addresses which means they are always on a local area network and behind a router. The two IPs cannot exist on the same network. All the ping Apr 14, 2013 · After few minutes another ping will issue. Router. Router#show clock 09:01:25.927 UTC Sun Apr 14 2013. Host. Host#ping 10.0.0.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds: UUUUU Success rate is 0 percent (0/5) Unsuccessful! And the time-range and access list statement should be active now. Router Understanding Basic Static Routing, Example: Configuring a Basic Set of Static Routes for Connecting to Stub Networks, Example: Configuring IPv6 Static Routes Information for IP address and browser: location, weather, client properties and more. Advanced Internet tools.
Jul 09, 2013 · Traceroute to the destination is also showing 10.0.1.1 and 10.0.0.2 are the number of hops to reach the destination. Here the destination is reachable but the hop 10.0.0.2 is not reachable . BRANCH#ping 192.168.0.1. Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.0.1, timeout is 2 seconds:!!!!!
Jul 02, 2012 · Summary: Guest blogger, Niklas Goude, discusses using Windows PowerShell to perform ping sweeps and port scans on a connected network. Microsoft Scripting Guy, Ed Wilson, is here. This week we have guest blogger Niklas Goude. Before we get to Niklas, I want to mention that you should mark your calendars for September 15, If 192.168.1.1 works, 10.0.0.1 never will and if 10.0.0.1 works 192.168.1.1 wont. Both ar private IP addresses which means they are always on a local area network and behind a router. The two IPs cannot exist on the same network. All the ping Apr 14, 2013 · After few minutes another ping will issue. Router. Router#show clock 09:01:25.927 UTC Sun Apr 14 2013. Host. Host#ping 10.0.0.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds: UUUUU Success rate is 0 percent (0/5) Unsuccessful! And the time-range and access list statement should be active now. Router Understanding Basic Static Routing, Example: Configuring a Basic Set of Static Routes for Connecting to Stub Networks, Example: Configuring IPv6 Static Routes Information for IP address and browser: location, weather, client properties and more. Advanced Internet tools. My router occasionally changes the LAN address from 192.168.1.1 to 10.0.01. When it does this, I have to go back and manually change it back. This is a problem because I have a couple of devices which have a fixed IP (e.g. Windows Home Server I have set to always use 192.168.1.50) Why does the rou